GLX-D+ Dual Band Digital Wireless offers confidence without complexity. Dual-band operation in 2.4 and 5.8 GHz more than doubles the available bandwidth to avoid interference without audio interruption. The receiver is compatible with a selection of lavalier, headset, and vocal microphones. The included lithium-ion battery offers up to 12 hours of runtime, and can be charged directly on the receiver or via USB-C.
Note: region dependent
① DC power connector | Connect DC power supply (9 to 15 V DC, 400 mA minimum). Note: Compatible with positive tip or negative tip power supplies. |
② INSTR IN | Use receiver as a wired guitar pedal tuner. |
③ INSTR OUT | Connect to amplifier or mixer. Note: If using multiple effects pedals, place the receiver pedal first in the signal chain. |
④ USB-C port | Connect to computer to download firmware updates. |
⑤ Display | Shows receiver and tuner settings. See below for more information on display controls. |
⑥ Antenna | Two antennas per receiver. Antennas pick up the signal from the transmitter. |
⑦ Footswitch | Press to select receiver or tuner mode. |
The controls and display offer specific functionality depending on which mode is selected:
① Transmitter battery meter | Illuminated segments indicate remaining battery life. |
② Display |
Group Channel LK (controls locked) UN (controls unlocked) -- (frequency not available) |
③ Link button | Press to manually link receiver to a transmitter or to activate the remote ID function. |
④ Mode button | Press to enable audio gain adjustment. Use ▲ ▼ buttons to adjust gain. |
⑤ Audio LED | Illumination corresponds to audio level. Rapid flashing indicates audio clipping. |
⑥ Mute LED | Illuminates when audio output is muted. |
⑦ RF LED |
|
⑧ Channel button | Press to select and edit channel. |
⑨ Group button | Press to select and edit group. |
① Flat indicator | Illuminates when note is flat. |
② Tuning bar display | LEDs illuminate to indicate tuning deviation. |
③ Sharp indicator | Illuminates when note is sharp. |
④ Note display | Displays the name of the note or (--) if the tuner is idle. |
⑤ Mode button | Press to enter tuner menu settings. |
⑥ Arrow buttons | Use ▲ ▼ buttons to select and edit menu settings. |
⑦ Frequency detuned/Reference pitch offset indicator | A dot is displayed when the tuning or pitch has been set to a non-standard value. Note: Non-standard tuning or pitch settings scroll across the receiver display during power-up. |
Note: The receiver powers on after the power supply and ¼" cable are connected.
① Antenna
Carries wireless signal.
② Status LED
LED color and state indicate transmitter status.
③ Power switch
Turns the transmitter on/off.
④ TA4M input port
Connects to a 4-Pin mini connector (TA4F) microphone or instrument cable.
⑤ USB-C charging port
Connect to USB battery charger.
⑥ Link button
⑦ Battery compartment
Holds 1 Shure rechargeable battery.
LED is green during normal operation.
LED color or flashing indicates a change in transmitter status as shown in the following table:
Color | State | Description |
---|---|---|
Green | Flashing (slow) | Transmitter attempting relink with receiver |
Flashing (fast) | Unlinked transmitter searching for receiver | |
Flashes 3 times | Indicates locked transmitter when power switch is pressed | |
Red | On | Battery life < 1 hour |
Flashing | Battery life < 30 minutes | |
Red/Green | Flashing | Remote ID active |
Amber | Flashing | Battery error; remove and insert again, or replace battery |
Clip the bodypack to a belt or slide a guitar strap through the bodypack clip as shown.
For best results, the belt should be pressed against the base of the clip.
Important: Always fully charge a new battery before first use.
GLX-D+ transmitters are powered by Shure SB904 lithium-ion rechargeable batteries. Advanced battery chemistry maximizes runtimes with zero memory effects, eliminating the need to discharge batteries prior to charging.
When not in use, recommended battery storage temperature is 10°C (50°F) to 25°C (77°F).
Note: The transmitter will not pass RF or audio signals when connected to the charging cable.
The following battery charging options are available:
LED Color | Description |
---|---|
Green (solid) | Device is fully charged |
Red (solid) | Charging |
Amber (flashing) | Out of temperature range, or battery error |
Off | Power supply is disconnected, or no device is docked in the charging bay |
Use the following table to determine approximate battery runtime based on the duration of charging time when in 5.8 GHz mode. Times shown are in hours and minutes. Transmitters automatically power-off after approximately 1 hour to conserve battery life if the signal from a linked receiver is not detected.
Receiver Bay or AC Power Source Charging | Transmitter Runtime |
---|---|
0:15 | up to 1:30 |
0:30 | up to 3:00 |
1:00 | up to 6:00 |
3:00 | up to 11:30* |
*Storage time or excessive heat will reduce maximum runtime.
Note: If receiver is powered off and remains plugged in, battery will continue charging.
The number of segments illuminated on the meter indicates the remaining battery life for a linked transmitter:
① = > 30 min
② = > 2 hours
③ = > 4 hours
④ = > 6 hours
⑤ = > 8 hours
⑥ = > 10 hours
⑦ = > 11.5 hours
Note: The LEDs will cycle on/off while battery life is being calculated.
Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.
If you encounter interference or dropouts, try the following suggestions:
Note: If transmitters are within 6 inches of non-GLX-D+ transmitters or microphone cartridges, audible noise is possible.
Transmitter gain has an adjustment range from -20 dB to +40 dB in 1 dB increments.
Tip: Try the 0 dB (unity gain) setting as a starting point, and then make gain adjustments if necessary.
Note: The intensity of the green audio LED corresponds to the audio level. Rapid flashing indicates audio clipping. Reduce the gain to remove the overload.
The controls of the receiver and transmitter can be locked to prevent unauthorized setting changes or power-off. The lock status is not changed by power cycles.
Simultaneously press and hold the group and channel buttons until LK appears on the screen. Repeat to unlock.
To lock directly from the transmitter:
Start with the transmitter off, then press and hold the link button while turning on the transmitter. Release the link button when the transmitter powers on to prevent an accidental factory reset. The lock icon appears on the receiver screen when locked. Repeat sequence to unlock.
To lock from the receiver front panel:
Simultaneously press and hold the group and link buttons for approximately 2 seconds until the flashing lock icon appears on the receiver screen. Repeat sequence to unlock.
Note: The transmitter status LED will flash if a locked switch is set to the off position.
Use the remote ID feature to identify linked transmitter and receiver pairs in multiple receiver systems.
To activate remote ID:
There are 3 band modes available for GLXD+ receivers.* The band mode options are:
Note: region dependent
To change the band mode:
Note: Linked receivers and transmitters must be able to operate in the same band. Transmitters that don’t support the selected band mode will unlink from the receiver.
Enter tuner mode by pressing the footswitch.
In tuner mode, the controls will only affect tuner functions. RF and audio settings are not affected.
Note:
Use the following buttons to select and edit the tuner menu settings:
The tuner indicator can be set to display a needle style or strobe style.
A single LED will illuminate on the tuning bar to indicate sharp or flat. The green center LED will illuminate when the note is in tune.
A sequence of three LEDs will travel across the tuning bar in the direction of sharp or flat. The LEDs will remain stationary when the note is in tune.
Note: Indicator and Output settings are displayed in a scroll from left to right.
Set the audio output to the following modes when the footswitch is pressed in tuner mode.
Note: Text for the output settings are displayed in a scroll from left to right.
Mode | Footswitch Function |
---|---|
Live | Receiver Display (audio Live) ↔ Tuner Display (audio Live) |
Mute | Receiver Display (audio Live) ↔ Tuner Display (audio Mute) |
Both* | Tuner Display (audio Mute) ↔ Tuner Display (audio Live) |
A/B** | Tuner Display (audio Live) ↔ Tuner Display (audio Live) |
* In Both mode, the pedal powers up in Receiver Display. Press the footswitch to enter tuner mode.
**In A/B mode, press the footswitch to easily switch between your transmitter (TX) and wired input (IN).
The receiver has a built-in light sensor to automatically adjust the display brightness.
To manually adjust the brightness choose one of the following settings:
The tuner can be set to display standard tuning for instruments that have been detuned up sharp or flat in the following increments:
The notation for standard tuning is b0
Note: A dot appears on the display as a reminder that the pedal is detuned.
Adds sharp or flat symbols to the display of non-natural notes.
The reference pitch can be offset from standard A440 in a range of 432 Hz to 447 Hz in 1 Hz increments.
When adjusting the pitch, the last 2 digits of the value will be displayed. For example, "32" would appear on the display when the pitch has been set to 432 Hz.
A dot appears on the display as a reminder that the reference pitch has been offset.
Both tuning indicators and the center green segment will illuminate when the note is in tune.
Both tuning indicators will illuminate and the strobe segments will remain stationary when the note is in tune.
To power your wireless receiver pedal, we recommend using the included power supply or a power supply with isolated power outputs.
If using a power supply with isolated power outputs, use a power outlet rated at a minimum of 400 mA.
However, if using other third-party power supplies:
New versions of the firmware can be uploaded and installed using the Shure Update Utility tool.
Download Shure Update Utility from shure.com
To update your firmware, connect the device to your computer using a USB-C cable and open the Shure Update Utility.
Use the reset function if it is necessary to restore the transmitter or receiver to their factory settings.
Restores the receiver to the following factory settings:
Press and hold the link button while turning on the receiver power until the display shows RE.
Note: When reset is complete, the receiver will automatically initiate linking to search for a transmitter. Press and hold the transmitter link button within five seconds of powering-on to complete the link.
Restores the transmitter to the following factory settings:
Press and hold the transmitter link button while turning on the transmitter until power LED turns off.
When the link button is released, the transmitter will automatically initiate linking to find an available receiver. Press the link button on an available receiver to relink.
Issue | Indicator Status | Solution |
---|---|---|
No sound or faint sound | Receiver RF LED on |
|
Receiver RF LED off |
|
|
Receiver display off |
|
|
Transmitter indicator LED flashing red | Charge or change transmitter battery. | |
Transmitter plugged into charger. | Disconnect transmitter from charger. | |
Audio artifacts or dropouts | RF LED flickering or off |
|
Distortion | OL indicator appears on receiver display | Reduce transmitter gain. |
Transmitter and receiver link unsuccessful | Transmitter and receiver LEDs flash to indicate that linking started, but the link fails | Update both components to the latest firmware version. |
Sound level variations when switching to different sources | N/A | Adjust transmitter gain as necessary. |
Receiver/transmitter won't turn off | Transmitter LED flashing rapidly | Controls locked. |
Receiver gain control cannot be adjusted | N/A | Check transmitter. Transmitter must be on to enable gain changes. |
Receiver controls cannot be adjusted | LK shown on receiver display when buttons are pressed | Controls locked. |
Transmitter ID function does not respond | Transmitter LED flashes green 3 times | Controls locked. |
Transmitter information does not appear on the receiver display | N/A | Linked transmitter is off or the receiver is not linked to a transmitter. |
Transmitter powers off after 1 hour | Transmitter status LED off | Transmitters automatically power-off after 1 hour to conserve battery life if the signal from a linked receiver is not detected. Make sure that linked receiver is turned on. |
Cable, Instrument, 2.5 foot (.75 m), 4 Pin Mini Connector (TA4F) to 1/4-inch Connector. | WA302 |
Cable, Instrument, 2-foot (0.7m), 4-pin Mini Connector (TA4F) with Right-Angle 1/4-inch Connector, used with Shure Wireless Bodypack Transmitters | WA304 |
Shure Rechargeable Battery | SB904 |
USB-C Battery Charger | SBC10-USBC |
Premium Guitar Cable TQG Threaded Connector | WA305 |
Power Supply | PS24 |
Z2 | 2400 - 2483.5 MHz |
Z3 | 2400 - 2483.5 MHz and 5725 - 5850 MHz |
Z4 | 2400 - 2483.5 MHz and 5725 - 5875 MHz |
Z5 | 2400 - 2483.5 MHz and 5725 - 5825 MHz |
Shure proprietary digital
10 mW E.I.R.P. maximum
0°C (32°F) to 50°C (122°F)
Positive voltage applied to the tip of the guitar cable phone plug produces positive voltage at the tip of the high impedance ¼-inch output
20 Hz – 20 kHz
120 dB, A-weighted
-88 dBm, typical
0.02%, typical
Up to 11.5 hours
Tuning Accuracy | ±1 cent |
Tuning Range | F#0 to C8 |
Up to 4 typical, 8 optimal
2.4 GHz only: Up to 4 typical, 5 optimal
9 V – 15 V, 400 mA (efficiency level VI power supply)
Dual-band PIFA
5.4 x 3.7 x 1.89 in. (138 x 95 x 48 mm)
19.75 oz (560 g)
Aluminum alloy
> 35 dB, typical
-20 to 40 dB in 1 dB steps
Tuner or True Bypass
6.35 mm (1/4") output
Impedance balanced
6.35 mm (1/4") output
100 Ω (50 Ω, Unbalanced)
6.35 mm (1/4") connector (into 3 kΩ load)
+8.5 dBV
6.35 mm (1/4") connector
Tip=audio, Ring=no audio, Sleeve=ground
50 Ω
-20 dBm
Shure Rechargeable Li-Ion Battery | SB904 |
USB Power Supply (US/Canada) | SBC10-USB15WSUSTWJ |
Dual-band Internal Monopole
4.5 x 2.6 x 1.1 in. (115 x 66.94 x 28.51 mm), (H x W x D)
5.4 oz (153.1 g), without battery
Aluminum alloy, ABS plastic
900 kΩ
4-pin male mini connector (TA4M)
+8.4 dBV (7.5 Vp-p)
Unbalanced
1 | Ground (cable shield) |
2 | + 5 V bias |
3 | Audio |
4 | Tied through active load to ground (on instrument adapter cable, pin 4 floats) |
Rechargeable Li-Ion
2420 mAh (8.71 Wh)
3.6 V
2.87 x 0.83 x 0.82 inches (72.8 x 20.96 x 20.80 mm), (H x W x D)
1.89 oz. (53.7 g)
PC/ABS
Charging: | 0°C (32°F) to 40°C (104°F) |
Operating: | -18 °C (0 °F) to 45 °C (113 °F) |
5 V
Operating:
0°C (32°F) to 40°C (104°F)
100 to 240 V AC
600 mA @ 100 V AC (full load)
5 v DC @ 3 A
15 W
100 to 240 V AC
200 mA @ 100 V AC (full load)
5 v DC @ 1 A
5 W
Group 1 | ||||||
---|---|---|---|---|---|---|
Gr 1 - Ch 1 | 2424 | 2425 | 2442 | 2443 | 2462 | 2464 |
Gr 1 - Ch 2 | 2418 | 2419 | 2448 | 2450 | 2469 | 2471 |
Gr 1 - Ch 3 | 2411 | 2413 | 2430 | 2431 | 2476 | 2477 |
Gr 1 - Ch 4 | 2405 | 2406 | 2436 | 2437 | 2455 | 2457 |
Group 2 | ||||||
---|---|---|---|---|---|---|
Gr 2 - Ch 1 | 2423 | 2424 | 2443 | 2444 | 2473 | 2474 |
Gr 2 - Ch 2 | 2404 | 2405 | 2426 | 2427 | 2456 | 2457 |
Gr 2 - Ch 3 | 2410 | 2411 | 2431 | 2432 | 2448 | 2449 |
Gr 2 - Ch 4 | 2417 | 2418 | 2451 | 2452 | 2468 | 2469 |
Gr 2 - Ch 5 | 2437 | 2438 | 2462 | 2463 | 2477 | 2478 |
Group 3 | |||
---|---|---|---|
Gr 3 - Ch 1 | 2415 | 2416 | 2443 |
Gr 3 - Ch 2 | 2422 | 2423 | 2439 |
Gr 3 - Ch 3 | 2426 | 2427 | 2457 |
Gr 3 - Ch 4 | 2447 | 2448 | 2468 |
Gr 3 - Ch 5 | 2409 | 2451 | 2452 |
Gr 3 - Ch 6 | 2431 | 2462 | 2463 |
Gr 3 - Ch 7 | 2404 | 2473 | 2474 |
Gr 3 - Ch 8 | 2435 | 2477 | 2478 |
Group 4 | |||||
---|---|---|---|---|---|
2404 | 2406 | 2408 | 2410 | 2412 | 2414 |
2416 | 2418 | 2420 | 2422 | 2424 | 2426 |
2428 | 2430 | 2432 | 2434 | 2436 | 2438 |
2440 | 2442 | 2444 | 2446 | 2448 | 2450 |
2452 | 2454 | 2456 | 2458 | 2460 | 2462 |
2464 | 2466 | 2468 | 2470 | 2472 | 2474 |
2476 | 2478 |
Group 1 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch 1 | 2405 | 2323 | 2441 | 2465 |
Gr 1 - Ch 2 | 2411 | 2429 | 2447 | 2471 |
Gr 1 - Ch 3 | 2417 | 2435 | 2453 | 2477 |
Group 2 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch 1 | 2404 | 2424 | 2444 | 2464 |
Gr 2 - Ch 2 | 2409 | 2429 | 2449 | 2469 |
Gr 2 - Ch 3 | 2414 | 2434 | 2454 | 2474 |
Gr 2 - Ch 4 | 2419 | 2439 | 2459 | 2478 |
Group 3 - Channel 1 (2.4 GHz) | |||||
---|---|---|---|---|---|
2405 | 2408 | 2411 | 2414 | 2417 | 2420 |
2423 | 2426 | 2429 | 2432 | 2435 | 2438 |
2441 | 2444 | 2447 | 2450 | 2453 | 2456 |
2459 | 2462 | 2465 | 2468 | 2471 | 2474 |
2477 |
Group 1 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch A | 5730 | 5760 | 5790 | 5820 |
Gr 1 - Ch B | 5736 | 5766 | 5796 | 5826 |
Gr 1 - Ch C | 5742 | 5772 | 5802 | 5832 |
Gr 1 - Ch D | 5748 | 5778 | 5808 | 5838 |
Gr 1 - Ch E | 5754 | 5784 | 5814 | 5845 |
Group 2 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch A | 5729 | 5759 | 5789 | 5819 |
Gr 2 - Ch B | 5734 | 5764 | 5794 | 5824 |
Gr 2 - Ch C | 5739 | 5769 | 5799 | 5829 |
Gr 2 - Ch D | 5744 | 5774 | 5804 | 5836 |
Gr 2 - Ch E | 5749 | 5779 | 5809 | 5841 |
Gr 2 - Ch F | 5754 | 5784 | 5814 | 5846 |
Group 3 - Channel A (5.8 GHz) | |||||
---|---|---|---|---|---|
5730 | 5733 | 5736 | 5739 | 5742 | 5745 |
5748 | 5751 | 5754 | 5757 | 5760 | 5763 |
5766 | 5769 | 5772 | 5775 | 5778 | 5781 |
5784 | 5787 | 5790 | 5793 | 5796 | 5799 |
5802 | 5805 | 5808 | 5811 | 5814 | 5817 |
5820 | 5823 | 5826 | 5829 | 5832 | 5835 |
5838 | 5841 | 5845 |
Group 1 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch 1 | 2405 | 2323 | 2441 | 2465 |
Gr 1 - Ch 2 | 2411 | 2429 | 2447 | 2471 |
Gr 1 - Ch 3 | 2417 | 2435 | 2453 | 2477 |
Group 2 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch 1 | 2404 | 2424 | 2444 | 2464 |
Gr 2 - Ch 2 | 2409 | 2429 | 2449 | 2469 |
Gr 2 - Ch 3 | 2414 | 2434 | 2454 | 2474 |
Gr 2 - Ch 4 | 2419 | 2439 | 2459 | 2478 |
Group 3 - Channel 1 (2.4 GHz) | |||||
---|---|---|---|---|---|
2405 | 2408 | 2411 | 2414 | 2417 | 2420 |
2423 | 2426 | 2429 | 2432 | 2435 | 2438 |
2441 | 2444 | 2447 | 2450 | 2453 | 2456 |
2459 | 2462 | 2465 | 2468 | 2471 | 2474 |
2477 |
Group 1 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch A | 5730 | 5766 | 5802 | 5838 |
Gr 1 - Ch B | 5736 | 5772 | 5808 | 5844 |
Gr 1 - Ch C | 5742 | 5778 | 5814 | 5851 |
Gr 1 - Ch D | 5748 | 5784 | 5820 | 5858 |
Gr 1 - Ch E | 5754 | 5790 | 5826 | 5864 |
Gr 1 - Ch F | 5760 | 5796 | 5832 | 5870 |
Group 2 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch A | 5729 | 5764 | 5799 | 5834 |
Gr 2 - Ch B | 5734 | 5769 | 5804 | 5839 |
Gr 2 - Ch C | 5739 | 5774 | 5809 | 5850 |
Gr 2 - Ch D | 5744 | 5779 | 5814 | 5856 |
Gr 2 - Ch E | 5749 | 5784 | 5819 | 5861 |
Gr 2 - Ch F | 5754 | 5789 | 5824 | 5866 |
Gr 2 - Ch G | 5759 | 5794 | 5829 | 5871 |
Group 3 - Channel A (5.8 GHz) | |||||
---|---|---|---|---|---|
5730 | 5733 | 5736 | 5739 | 5742 | 5745 |
5748 | 5751 | 5754 | 5757 | 5760 | 5763 |
5766 | 5769 | 5772 | 5775 | 5778 | 5781 |
5784 | 5787 | 5790 | 5793 | 5796 | 5799 |
5802 | 5805 | 5808 | 5811 | 5814 | 5817 |
5820 | 5823 | 5826 | 5829 | 5832 | 5835 |
5838 | 5841 | 5844 | 5847 | 5851 | 5855 |
5858 | 5861 | 5864 | 5867 | 5870 |
Group 1 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch 1 | 2405 | 2323 | 2441 | 2465 |
Gr 1 - Ch 2 | 2411 | 2429 | 2447 | 2471 |
Gr 1 - Ch 3 | 2417 | 2435 | 2453 | 2477 |
Group 2 (2.4 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch 1 | 2404 | 2424 | 2444 | 2464 |
Gr 2 - Ch 2 | 2409 | 2429 | 2449 | 2469 |
Gr 2 - Ch 3 | 2414 | 2434 | 2454 | 2474 |
Gr 2 - Ch 4 | 2419 | 2439 | 2459 | 2478 |
Group 3 - Channel 1 (2.4 GHz) | |||||
---|---|---|---|---|---|
2405 | 2408 | 2411 | 2414 | 2417 | 2420 |
2423 | 2426 | 2429 | 2432 | 2435 | 2438 |
2441 | 2444 | 2447 | 2450 | 2453 | 2456 |
2459 | 2462 | 2465 | 2468 | 2471 | 2474 |
2477 |
Group 1 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 1 - Ch A | 5730 | 5754 | 5778 | 5802 |
Gr 1 - Ch B | 5736 | 5760 | 5784 | 5808 |
Gr 1 - Ch C | 5742 | 5766 | 5790 | 5814 |
Gr 1 - Ch D | 5748 | 5772 | 5796 | 5820 |
Group 2 (5.8 GHz) | ||||
---|---|---|---|---|
Gr 2 - Ch A | 5729 | 5753 | 5778 | 5803 |
Gr 2 - Ch B | 5733 | 5758 | 5783 | 5808 |
Gr 2 - Ch C | 5738 | 5763 | 5788 | 5813 |
Gr 2 - Ch D | 5743 | 5768 | 5793 | 5817 |
Gr 2 - Ch E | 5748 | 5773 | 5798 | 5821 |
Group 3 - Channel A (5.8 GHz) | |||||
---|---|---|---|---|---|
5730 | 5733 | 5736 | 5739 | 5742 | 5745 |
5748 | 5751 | 5754 | 5757 | 5760 | 5763 |
5766 | 5769 | 5772 | 5775 | 5778 | 5781 |
5784 | 5787 | 5790 | 5793 | 5796 | 5799 |
5802 | 5805 | 5808 | 5811 | 5814 | 5817 |
5820 |
![]() |
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. |
![]() |
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. |
In the European Union and the United Kingdom, this label indicates that the batteries in this product should be collected separately and not be disposed of with household waste. Substances in batteries can have a potential negative impact on health and environment and you have a role in recycling waste batteries thus contributing to the protection, preservation, and improvement of the quality of the environment. You should contact your local authority or retailer for details of the collection and recycling schemes available.
The equipment is intended to be used in professional audio applications.
EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.
Please consider the environment, electric products and packaging are part of regional recycling schemes and do not belong to regular household waste.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception.
Notice: The FCC regulations provide that changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
Shure has determined that this product is a Class B harmonized product. The following sections provide country-specific EMC/EMI or product safety information.
Certified under FCC Part 15.
FCC ID: DD4GLXD4RZ3, DD4GLXD1Z3, DD4GLXD2Z3 IC: 616A-GLXD4RZ3, 616A-GLXD1Z3, 616A-GLXD2Z3
CAN ICES-003 (B)/NMB-003(B)
The antenna(s) must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times.
La ou les antennes doivent être installées de telle façon qu'une distance de séparation minimum de 20 cm soit maintenue entre le radiateur (antenne) et toute personne à tout moment.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Certified by ISED in Canada under RSS-247 and RSS-GEN.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Para maiores informações, consulte o site da ANATEL – http://www.anatel.gov.br.
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음
เครื่องโทรคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกำหนดทางเทคนิคของ กสทช.
Paraguay Distributor: Microsystems S.R.L., Senador Long 664 c/Dr. Lilio, Asunción, Paraguay
Connection and use of this communications equipment is permitted by the Nigerian Communications Commission.
運用に際しての注意
この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほか工場の製造ライン等で使用されている移動体識別用の構内無線局(免許を要する無線局)及び特定小電力無線局(免許を要しない無線局)並びにアマチュア無線局(免許を要する無線局)が運用されています。
現品表示記号について
現品表示記号は、以下のことを表しています。 この無線機器は 2.4GHz 帯の電波を使用し、変調方式は「その他」の方式、想定与干渉距離は 80m です。 2,400MHz~ 2,483.5MHz の全帯域を使用し、移動体識別装置の帯域を回避することはできません。
In the European Union and the United Kingdom, this label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
Registration, Evaluation, Authorization of Chemicals (REACH) Directive
REACH (Registration, Evaluation, Authorization of Chemicals) is the European Union (EU) and the United Kingdom (UK) chemical substances regulatory framework. Information on substances of very high concern contained in Shure products in a concentration above 0.1% weight over weight (w/w) is available upon request.
Hereby, Shure Incorporated declares that this product with CE Marking has been determined to be in compliance with European Union requirements. The full text of the EU declaration of conformity is available at the following site: https://www.shure.com/en-EU/support/declarations-of-conformity.
Authorized European Importer:
Shure Europe GmbH
Department: Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: EMEAsupport@shure.de
Hereby, Shure Incorporated declares that this product with UKCA Marking has been determined to be in compliance with UKCA requirements. The full text of the UK declaration of conformity is available at the following site: https://www.shure.com/en-GB/support/declarations-of-conformity.
Shure UK Limited - UK Importer
Unit 2, The IO Centre, Lea Road,
Waltham Abbey, Essex, EN9 1 AS, UK
(一)本产品符合“微功率短距离无线电发射设备目录和技术要求”的具体条款和使用场景;
(二)不得擅自改变使用场景或使用条件、扩大发射频率范围、加大发射功率(包括额外加装射频功率放大器),不得擅自更改发射天线;
(三)不得对其他合法的无线电台(站)产生有害干扰,也不得提出免受有害干扰保护;
(四)应当承受辐射射频能量的工业、科学及医疗(ISM)应用设备的干扰或其他合法的无线电台(站)干扰;
(五)如对其他合法的无线电台(站)产生有害干扰时,应立即停止使用,并采取措施消除干扰后方可继续使用;
(六)在航空器内和依据法律法规、国家有关规定、标准划设的射电天文台、气象雷达站、卫星地球站(含测控、测距、接收、导航站)等军民用无线电台(站)、机场等的电磁环境保护区域内使用微功率设备,应当遵守电磁环境保护及相关行业主管部门的规定。