Explanation of Symbols
|Caution: risk of electric shock|
|Caution: risk of danger (See note.)|
|Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION|
|Equipment should not be disposed of in the normal waste stream|
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting.
Caution: Do not transport chargers with batteries inserted.
Warning: Do not charge batteries in enclosed spaces without proper ventilation.
Please follow your regional recycling scheme for batteries, packaging, and electronic waste.
Note: Model information and power ratings are labeled on the bottom of the unit.
The SBC220 networked docking charger provides a compact charging and storage solution for any combination of 2 SB900 or SB900A batteries or the following wireless transmitters using Shure rechargeable batteries:
Note: P3RA and P9HW universal bodypacks are also compatible with SBC220, but they must be kept powered on with the “Auto Off” feature disabled while charging and monitoring. UR5 universal bodypacks are not compatible with SBC220.
The charger is network-enabled to allow for remote monitoring of charger and battery parameters using Shure Wireless Workbench® software. Connect up to 4 SBC220 or SBC240 chargers together to share power and network connectivity.
Note: Model availability depends on region. See your local Shure dealer or distributor for details.
① Power LED
② Reset Button
Press and hold to restore charger factory settings, including network settings.
③ Storage Mode Button
Press and hold to activate storage mode, which charges or discharges batteries to the optimal voltage for long-term storage.
④ Charging Status LED
⑤ Error LED
Flashes amber to indicate a problem charging batteries. Errors are also displayed in Wireless Workbench. See LED Indicators for details.
⑥ Charging Slots
Charges any combination of 2 supported batteries or transmitters.
⑦ Ethernet Port
Connect to a network to remotely monitor batteries and control charger settings using Wireless Workbench.
⑧ Ethernet Link Speed LED (Amber)
⑨ Ethernet Status LED (Green)
⑩ Power Input
Connect to power supply.
⑪ Charger Connector (with rubber covers)
Use supplied screws and Allen wrench to connect up to 4 chargers to 1 power supply.
The charger has no power switch. When plugged in, the power LED illuminates. The charging LEDs illuminate after batteries are inserted.
Use power save mode to charge batteries with the charger’s network functionality off.
The charger remains in power save mode until you power off the charger.
Note: Transmitters docked with the power switch in the ON position will power on when fully charged. To avoid unwanted audio and unnecessary battery drain, ensure all transmitters are switched OFF before charging.
To save space and reduce clutter, a combination of up to 4 SBC220 and SBC240 chargers can share 1 power supply and Ethernet connection.
Important: Do not overtighten.
Note: A maximum of 4 chargers can share power and network connectivity. Only connect SBC220 and SBC240 chargers to the charger connectors.
To charge, place batteries and transmitters into the charging bays as shown, with the LCD facing the charging LEDs. The LEDs illuminate to indicate battery status.
Warning: Do not insert transmitters using AA batteries.
|Charge status LED red||Charging|
|Charge status LED green||Charging complete|
|Error LED amber flashing||Charging stopped. To resume charging, try these solutions:
||Too many chargers (more than 4) are connected to each other. Remove additional chargers.|
||Battery too warm. Charging stops at 80% of full capacity. Allow battery to cool below 45°C to resume charging to full capacity.|
||Charging complete, but battery temperature is too warm or cold (over 60°C or below 0°C).|
|Power LED red||Charger is in storage mode. Batteries are charging or discharging to storage voltage.|
||Batteries are ready for storage.|
||Batteries are approaching storage voltage.|
|Power LED white flashing||Charger firmware is being updated.|
|All LEDs flashing||Hardware identification.|
Tip: Wireless Workbench provides more detailed battery status information, including temperature and overall health.
To store batteries for longer than 8 days, use the charger's storage mode. Each battery will be charged or discharged to 3.8 volts, which is ideal for long-term storage.
To enter storage mode, press and hold storage for 3 seconds until the power LED turns red. The batteries will begin charging or discharging to 3.8 volts, which may take several hours. The LEDs indicate when the battery is approaching storage voltage or at storage voltage.
To exit storage mode, press and hold storage. The power LED changes to white and batteries resume charging normally.
When batteries are ready for storage, remove them from the charger and place in a temperature-controlled area. Recommended battery storage temperature is 10°C (50°F) to 25°C (77°F).
Note: Run storage mode once every 6 months to maintain the storage voltage.
Press and hold reset to restore factory settings. All LEDs will flash and turn off as the charger reboots.
IP addressing will be set to automatic, and charger will be in charging mode.
Wireless Workbench lets you control and monitor devices over the network. To get started, visit http://www.shure.com/wwb and download Wireless Workbench software. Wireless Workbench communicates with connected devices over a standard Ethernet network.
Required equipment: Shure device, computer with Wireless Workbench installed, Cat 5 (or better) Ethernet cable, and router or network switch
For more help, visit the Help menu in Wireless Workbench or http://www.shure.com/wwb.
Wireless Workbench provides detailed information for batteries currently docked in the charger. You can also view battery error notifications and change the charger's network settings.
Click the Inventory tab to view your charger in Wireless Workbench. The charger properties panel provides different battery statistics:
Displays charge as a percentage of the total battery capacity. Also shows time remaining to full charge.
Displays health of selected battery as a percentage of the charge capacity of a new battery. Charge capacity (battery life when fully charged) will decline as a result of repeated charge cycles, age, or storage conditions.
Displays total number of times that the battery has undergone one full count of discharge and charge. Recharging after discharging halfway counts as one half of a cycle. Recharging after discharging a quarter of the way counts as one quarter of a cycle.
Displays battery temperature (in Celsius and Fahrenheit) and status.
To adjust charger network settings, open the charger properties panel in Wireless Workbench. Click the gear icon to set the IP mode and IP address, view the MAC address, and view firmware version.
The SBC220 networked charger connects to external control systems such as AMX or Crestron via the Ethernet. For a comprehensive list of command strings, visit the product page at https://www.shure.com.
Three mounting points on the bottom of the charger fit #6 round or pan head screws. Mount to a hard surface using 3 screws that are long enough to secure the charger. To mount, orient the charger so that the 2 mounting points are on top as shown.
Warning: Only charge SB900 batteries in charger when it is mounted vertically. Do not charge transmitters.
All include power supply unless otherwise noted.
|Global||SBC220 (no power supply)|
Up to 2 SB900/SB900A
Up to 2 ULXD1, ULXD2, QLXD1, QLXD2, AD1 or AD2
0.75 A maximum
1 hour = 50% charged; 3 hours = 100% charged
15 V, 4 A maximum
66.31 x 88.74 x 210.82 mm (2.61 x 3.49 x 8.30 in.) H x W x D
0.45 kg (1 lb) without batteries
0°C (32°F) to 45°C (113°F)
-29°C (-20°F) to 74°C (165°F)
10/100 Mbps Ethernet
DHCP or Manual IP address
Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Authorized under the verification provision of FCC Part 15B.
CAN ICES-3 (B)/NMB-3 (B)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.
Please consider the environment, electric products and packaging are part of regional recycling schemes and do not belong to regular household waste.