Shure Sound Isolating™ Earphones, built with balanced armature speakers, deliver a detailed soundstage free from outside noise. The powerful and stylish Shure SE earphones come with a detachable cable, adapters, a durable carrying case, and interchangeable Sound Isolating sleeves for a comfortable and personalized fit.
You may need to detach the cable from the earphones to attach optional components or to replace the cable if it becomes damaged. To prevent accidental separation, the connector has a snug fit. Take special care to prevent damage to the earphone and connector.
Note: If you pull at an angle, the connector will not detach.
The following are some suggested ways of wearing the earphones.
Wear the cable over the ear and secure it behind the head to help keep the earphones in place during physical activity.
Tighten the cable and take up slack by raising the cable cinch.
Insert the earphones so they form a tight seal. The fit of the earphone can greatly affect sound quality.
Important: If there seems to be a lack of low frequency response (bass), this means that the earphone sleeve is not forming a tight seal. Gently push the earphone deeper into the ear canal or try a different sleeve.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
Caution: If the barb or any of the nozzle is exposed, the sleeve is not properly installed. Replace sleeves if they do not tightly grip the nozzle. To ensure proper fit and performance, use only sleeves supplied by Shure (unless using custom molded sleeves).
Grasp the body of earphone and gently twist to remove.
Note: Do not pull on cable to remove earphone.
Select an earphone sleeve that provides the best fit and sound isolation. It should be easy to insert, fit comfortably, and easy to remove.
|Soft Flex Sleeves: In small, medium, and large sizes. Made from pliable rubber.|
|Soft Foam Sleeves: Compress the foam sleeve between your fingers and insert into the ear canal. Hold in place for about ten seconds while the foam expands.|
|Triple-Flange Sleeves: If desired, use scissors to trim the stem on the sleeve.|
If you notice a change in sound quality, remove the sleeve and check the nozzle of your earphone. If nozzle is blocked, clear obstruction by using wire loop end of cleaning tool.
If no obstruction is found or if sound quality does not improve, replace the sleeve with a new sleeve.
Caution: When cleaning, do not force any object through the earphone nozzle! This will damage the earphone sound filter.
Warning: The cleaning tool is only to be used to clean the earphones. Any other use, such as using the tool to clean ears or foam sleeve, could result in injury.
The cable connectors to the earphones may collect debris or other deposits that can affect audio quality. If this happens, disconnect the cables and clean them using a dry cotton swab.
Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product safety.
|SE535/535LTD Red||Triple balanced-armature drivers|
|SE425||Dual balanced-armature drivers|
|SE315||Single High-Definition MicroDriver|
at 1 kHz
|SE535/535LTD Red||119 dB SPL/MW|
|SE425||109 dB SPL/MW|
|SE315||116 dB SPL/MW|
at 1 kHz
|SE535/535LTD Red||36 Ω|
|SE535||18 Hz –19 kHz|
|SE535LTD Red||18 Hz –19 .5 kHz|
|SE425||20 Hz –19 kHz|
|SE315||22 Hz –18 .5 kHz|
Gold-plated 3.5 mm (1/8”) stereo mini jack plug with 6.35 mm (1/4”) threaded adapter
30 g (1 oz.)
-18°C to 57°C (0°F to 135°F)
-29°C to 74°C (-20°F to 165°F)
For information about earphone accessories and other Shure products visit:
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4